Xiaoxia
e9582601e0
- Incremented project version from 2.4.1 to 2.4.2 in CMakeLists.txt. - Added support for `--build-options-json` in firmware_builder.py to allow custom build options. - Implemented validation for build options to ensure correct data types and structure. - Updated tests to cover new build options functionality and validation logic.
97 lines
3.5 KiB
C
97 lines
3.5 KiB
C
#ifndef _BOARD_CONFIG_H_
|
||
#define _BOARD_CONFIG_H_
|
||
|
||
#include <driver/gpio.h>
|
||
|
||
// ES8389 音频编解码芯片 + 双 NS4150B 功放
|
||
#define AUDIO_INPUT_SAMPLE_RATE 16000
|
||
#define AUDIO_OUTPUT_SAMPLE_RATE 16000
|
||
|
||
// 依据官方 esp-bsp（esp32_s31_korvo_1）
|
||
#define AUDIO_I2S_GPIO_MCLK GPIO_NUM_2
|
||
#define AUDIO_I2S_GPIO_BCLK GPIO_NUM_3
|
||
#define AUDIO_I2S_GPIO_WS GPIO_NUM_4
|
||
#define AUDIO_I2S_GPIO_DIN GPIO_NUM_6
|
||
#define AUDIO_I2S_GPIO_DOUT GPIO_NUM_5
|
||
|
||
#define AUDIO_CODEC_I2C_SDA_PIN GPIO_NUM_0
|
||
#define AUDIO_CODEC_I2C_SCL_PIN GPIO_NUM_1
|
||
#define AUDIO_CODEC_PA_PIN GPIO_NUM_7
|
||
#define AUDIO_CODEC_ES8389_ADDR ES8389_CODEC_DEFAULT_ADDR
|
||
#define AUDIO_CODEC_USE_MCLK false
|
||
#define AUDIO_INPUT_CHANNELS 2 // 双模拟麦克风阵列
|
||
#define AUDIO_OUTPUT_CHANNELS 2 // 立体声输出，双 NS4150B 功放
|
||
|
||
// 板载用户控件
|
||
#define BUILTIN_LED_GPIO GPIO_NUM_37
|
||
#define BOOT_BUTTON_GPIO GPIO_NUM_61
|
||
|
||
// 4 个 ADC 按键（SET/MODE/VOL-/VOL+），电阻分压网络
|
||
#define ADC_BUTTON_GPIO GPIO_NUM_42
|
||
|
||
// ADC 按键中心电压（mV），官方 BSP 校准数据（配合 esp32_s31_adc_calibration.c
|
||
// 的软件校准使用，校准后读数与分压理论值一致）。
|
||
// 按键窗口按官方算法取相邻键中点自动划分。
|
||
// 注意：S31 的 SAR ADC 原始值是反相的（电压越高 raw 越小），
|
||
// 未经校准的直读公式会得出相反的键序，请勿以此判断键位。
|
||
#define ADC_BUTTON_SET_MV 1870
|
||
#define ADC_BUTTON_MODE_MV 1340
|
||
#define ADC_BUTTON_VOL_DOWN_MV 820
|
||
#define ADC_BUTTON_VOL_UP_MV 380
|
||
#define ADC_BUTTON_IDLE_MV 2000
|
||
|
||
// LCD 子板：RGB 16 位面板（ST7262E43），800x480 横屏。
|
||
// 背光硬件常开；复位/触摸中断线未连接。
|
||
#define DISPLAY_WIDTH 800
|
||
#define DISPLAY_HEIGHT 480
|
||
#define DISPLAY_MIRROR_X false
|
||
#define DISPLAY_MIRROR_Y false
|
||
#define DISPLAY_SWAP_XY false
|
||
#define DISPLAY_OFFSET_X 0
|
||
#define DISPLAY_OFFSET_Y 0
|
||
|
||
#define LCD_RGB_VSYNC GPIO_NUM_45
|
||
#define LCD_RGB_HSYNC GPIO_NUM_44
|
||
#define LCD_RGB_DE GPIO_NUM_43
|
||
#define LCD_RGB_PCLK GPIO_NUM_40
|
||
#define LCD_RGB_DISP GPIO_NUM_38
|
||
#define LCD_RGB_DATA0 GPIO_NUM_8
|
||
#define LCD_RGB_DATA1 GPIO_NUM_9
|
||
#define LCD_RGB_DATA2 GPIO_NUM_10
|
||
#define LCD_RGB_DATA3 GPIO_NUM_11
|
||
#define LCD_RGB_DATA4 GPIO_NUM_12
|
||
#define LCD_RGB_DATA5 GPIO_NUM_13
|
||
#define LCD_RGB_DATA6 GPIO_NUM_14
|
||
#define LCD_RGB_DATA7 GPIO_NUM_15
|
||
#define LCD_RGB_DATA8 GPIO_NUM_16
|
||
#define LCD_RGB_DATA9 GPIO_NUM_17
|
||
#define LCD_RGB_DATA10 GPIO_NUM_18
|
||
#define LCD_RGB_DATA11 GPIO_NUM_19
|
||
#define LCD_RGB_DATA12 GPIO_NUM_33
|
||
#define LCD_RGB_DATA13 GPIO_NUM_34
|
||
#define LCD_RGB_DATA14 GPIO_NUM_35
|
||
#define LCD_RGB_DATA15 GPIO_NUM_36
|
||
|
||
// GT1151 触摸，与 codec 共享 I2C 总线（无复位/中断线）
|
||
|
||
// OV3660 摄像头，DVP 接口（SCCB 与 codec 共享 I2C 总线，地址 0x78）。
|
||
// 参数以官方 factory demo 的 BSP 实测值为准：XCLK 20MHz，SCCB 10kHz。
|
||
#define CAMERA_PIN_XCLK GPIO_NUM_55
|
||
#define CAMERA_PIN_PCLK GPIO_NUM_54
|
||
#define CAMERA_PIN_VSYNC GPIO_NUM_56
|
||
#define CAMERA_PIN_HREF GPIO_NUM_57
|
||
#define CAMERA_PIN_D0 GPIO_NUM_46
|
||
#define CAMERA_PIN_D1 GPIO_NUM_47
|
||
#define CAMERA_PIN_D2 GPIO_NUM_48
|
||
#define CAMERA_PIN_D3 GPIO_NUM_49
|
||
#define CAMERA_PIN_D4 GPIO_NUM_50
|
||
#define CAMERA_PIN_D5 GPIO_NUM_51
|
||
#define CAMERA_PIN_D6 GPIO_NUM_52
|
||
#define CAMERA_PIN_D7 GPIO_NUM_53
|
||
#define CAMERA_PIN_RESET GPIO_NUM_NC
|
||
#define CAMERA_PIN_PWDN GPIO_NUM_NC
|
||
#define CAMERA_XCLK_FREQ_HZ (20 * 1000 * 1000)
|
||
#define CAMERA_SCCB_FREQ_HZ (10 * 1000)
|
||
|
||
#endif // _BOARD_CONFIG_H_
|